home chevron_right Productschevron_rightMTZ-35
Impedance analyzer

MTZ-35.

An advanced, comprehensive solution for the electrical characterization of materials

An impedance analyzer with the features and specifications necessary for working on a the broad range of applications in the field of materials research.

Request a quote

An advanced, comprehensive solution for the electrical characterization of materials

A modern materials science lab faces challenging measurements every day, and impedance spectroscopy is a primary tool in materials research enabling the characterization of the electrical properties of materials.

With a wide frequency range (10 µHz – 35 MHz) and high-levels of accuracy (0.1% amplitude, 0.05% phase) the BioLogic MTZ-35 impedance analyzer has been designed to tackle even the most difficult measurements required by materials science.

The MTZ-35 is the key instrument in integrated solutions for the electrical characterization of materials. These solutions, dedicated to wide-ranging applications and temperature ranges, consist of the MTZ-35 impedance analyzer, a temperature control unit, a sample holder and MT-lab software. The MT-Lab interface allows the control of many temperature control systems (HTF-1100 furnace, ITS, etc.) over a wide temperature range (from -40 to 1100°C).  It also allows impedance measurement and the modeling of EIS data with equivalent circuits. Many sample holders (CESH, HTSH-1100, HTCC) covering various materials types (polymers, ceramics, composites, ionic liquids, gels, etc) are compatible with the MTZ-35.

 

An intuitive and comprehensive software

MT-Lab® is an intuitive and user-friendly software dedicated to the control of Bio-Logic’s impedance analyzer, the acquisition of the impedance data and the temperature. It also allows the control of many temperature control units:

  • High-temperature furnace (HTF-1100)
  • Intermediate Temperature System (ITS)
  • Temperature control systems using Eurotherm 22xx and 35xx series controllers…

Specifications

  • Generator

    • Frequency Range: 10 μHz to 35 MHz
      Voltage range DC: ±100 μV to ±10 V
      Voltage range AC: 100 μV to 10 V

    Measurement Ranges

    • Inductance 10 nH to 10 kH
    • Capacitance 1 pF to 1000 μF
    • Resistance 1 mΩ to 500 MΩ
    • Basic Accuracy 0.1%

MTZ-35 Brochure

An advanced solution for the electrical characterization of materials
Download

Material Testing catalog

Integrated solution for Materials Characterization under wide temperature range and controlled atmospheres
Download

Leaflet All Solid-State Batteries

A comprehensive solution to empower innovation
Download

Electrochemistry Instrument catalog

A unique and comprehensive range of instruments for the field of electrochemistry
Download

Electrochemistry Accessory catalog

An extensive line of product accessories ranging from sophisticated quartz crystal microbalances to electrodes.
Download

Impedance compensation <em><span>Material Science – </span>Application Note 4</em>

AN 4.Impedance compensation – Materials Science
Download

The influence of interfacial interactions on the conductivity and phase behaviour of organic ionic plastic crystal/polymer nanoparticle composite electrolytes

CITATION: Frederick Nti, Luca Porcarelli, George W. Greene, Haijin Zhu, Faezeh Makhlooghiazad, David Mecerreyes, Patrick C. Howlett, Maria Forsyth, Xiaoen Wang
More info

Polymerized Ionic Liquid Block Copolymer Electrolytes for All-Solid-State Lithium-Metal Batteries

CITATION: Tiago C. Mendes, Nicolas Goujon, Nino Malic, Almar Postma, John Chiefari, Haijin Zhu, Patrick C. Howlett1 and Maria Forsyth
More info

Plastic Crystals Utilising Small Ammonium Cations and Sulfonylimide Anions as Electrolytes for Lithium Batteries

CITATION: Ruhamah Yunis, Danah Al-Masri1, Anthony F. Hollenkamp, Cara M. Doherty, Haijin Zhu and Jennifer M. Pringle
More info

4D-resolved physical model for Electrochemical Impedance Spectroscopy of Li(Ni1-x-yMnxCoy)O2-based cathodes in symmetric cells: Consequences in tortuosity calculations

CITATION: Abbos Shodiev, Emiliano N.Primo, Mehdi Chouchane, Teo Lombardo, Alain C.Ngandjong, Alexis Rucci, Alejandro A.Franco
More info

Ion interactions and dynamics in pseudohalide based ionic liquid electrolytes containing sodium solutes

CITATIONS: Matthias Hilder, Tony Pointu, Haijin Zhua, Michel Armand, Patrick Howletta, Maria Forsytha
More info

Enhanced rate capabilities in a glass-ceramic-derived sodium all-solid-state battery

CITATION: Hideo Yamauchi, Junichi Ikejiri, Kei Tsunoda, Ayumu Tanaka, Fumio Sato, Tsuyoshi Honma & Takayuki Komatsu
More info
See all documentation

I receive many cell cables with MTZ-35 which one should I use?

The MTZ-35 is provided with two sets of cables:

  • A set of four cables (x1 m) for four-point measurement dedicated for impedance measurements on low impedance samples (lower than 1 Ω)
  • A set of three cables with a Tee connector for two-point measurement for impedance measurements on intermediate and high impedance samples. More details can be found in the TN#05

My MTZ-35 does not beep when I turn it on? How can I proceed?

If the power led is off when you switch on the MTZ-35, check the fuses located on the rear panel of the instrument. If a fuse is blown replace it with a new one rated at 3.15A. You can use the two 2A rapid fuses provided at the purchase of the MTZ-35.

How do I check the accuracy of results given by the MTZ-35?

Any instrument is prone to a drift in its accuracy with time and use. In order to check the accuracy of the MTZ-35, use a high accuracy resistor or capacitor and check the measured resistance/capacitance with their corresponding nominal resistance/capacitance.

Which communication port should I connect the MTZ-35 to?

When you install MT-Lab® software the driver of the MTZ-35 is also installed and two virtual communication ports are generated. To access to these communication ports go to “Control Panel”>”External Devices”> “Ports(COM & LPT)”. You can see two virtual communication ports “USB serial port (COM N)” and “USB serial port (COM N+1)”. Select the one with the high order (COM N+1).

I performed a measurement on a capacitor with a nominal capacitance 100 pF I got 320 pF capacitance value. Do I need to calibrate my MTZ-35?

The measured capacitance should coincide with the nominal capacitance. your measurement seems to be performed without compensation. Perform open-circuit and short circuit compensation and then perform impedance measurement on the capacitor. More details can be found in the TN#01 and AN#04

Description

An advanced, comprehensive solution for the electrical characterization of materials

A modern materials science lab faces challenging measurements every day, and impedance spectroscopy is a primary tool in materials research enabling the characterization of the electrical properties of materials.

With a wide frequency range (10 µHz – 35 MHz) and high-levels of accuracy (0.1% amplitude, 0.05% phase) the BioLogic MTZ-35 impedance analyzer has been designed to tackle even the most difficult measurements required by materials science.

The MTZ-35 is the key instrument in integrated solutions for the electrical characterization of materials. These solutions, dedicated to wide-ranging applications and temperature ranges, consist of the MTZ-35 impedance analyzer, a temperature control unit, a sample holder and MT-lab software. The MT-Lab interface allows the control of many temperature control systems (HTF-1100 furnace, ITS, etc.) over a wide temperature range (from -40 to 1100°C).  It also allows impedance measurement and the modeling of EIS data with equivalent circuits. Many sample holders (CESH, HTSH-1100, HTCC) covering various materials types (polymers, ceramics, composites, ionic liquids, gels, etc) are compatible with the MTZ-35.

 

Software

An intuitive and comprehensive software

MT-Lab® is an intuitive and user-friendly software dedicated to the control of Bio-Logic’s impedance analyzer, the acquisition of the impedance data and the temperature. It also allows the control of many temperature control units:

  • High-temperature furnace (HTF-1100)
  • Intermediate Temperature System (ITS)
  • Temperature control systems using Eurotherm 22xx and 35xx series controllers…
Specifications

Specifications

  • Generator

    • Frequency Range: 10 μHz to 35 MHz
      Voltage range DC: ±100 μV to ±10 V
      Voltage range AC: 100 μV to 10 V

    Measurement Ranges

    • Inductance 10 nH to 10 kH
    • Capacitance 1 pF to 1000 μF
    • Resistance 1 mΩ to 500 MΩ
    • Basic Accuracy 0.1%
Documentation
See all documentation
FAQ

I receive many cell cables with MTZ-35 which one should I use?

The MTZ-35 is provided with two sets of cables:

  • A set of four cables (x1 m) for four-point measurement dedicated for impedance measurements on low impedance samples (lower than 1 Ω)
  • A set of three cables with a Tee connector for two-point measurement for impedance measurements on intermediate and high impedance samples. More details can be found in the TN#05

My MTZ-35 does not beep when I turn it on? How can I proceed?

If the power led is off when you switch on the MTZ-35, check the fuses located on the rear panel of the instrument. If a fuse is blown replace it with a new one rated at 3.15A. You can use the two 2A rapid fuses provided at the purchase of the MTZ-35.

How do I check the accuracy of results given by the MTZ-35?

Any instrument is prone to a drift in its accuracy with time and use. In order to check the accuracy of the MTZ-35, use a high accuracy resistor or capacitor and check the measured resistance/capacitance with their corresponding nominal resistance/capacitance.

Which communication port should I connect the MTZ-35 to?

When you install MT-Lab® software the driver of the MTZ-35 is also installed and two virtual communication ports are generated. To access to these communication ports go to “Control Panel”>”External Devices”> “Ports(COM & LPT)”. You can see two virtual communication ports “USB serial port (COM N)” and “USB serial port (COM N+1)”. Select the one with the high order (COM N+1).

I performed a measurement on a capacitor with a nominal capacitance 100 pF I got 320 pF capacitance value. Do I need to calibrate my MTZ-35?

The measured capacitance should coincide with the nominal capacitance. your measurement seems to be performed without compensation. Perform open-circuit and short circuit compensation and then perform impedance measurement on the capacitor. More details can be found in the TN#01 and AN#04

I receive many cell cables with MTZ-35 which one should I use?

The MTZ-35 is provided with two sets of cables:

  • A set of four cables (x1 m) for four-point measurement dedicated for impedance measurements on low impedance samples (lower than 1 Ω)
  • A set of three cables with a Tee connector for two-point measurement for impedance measurements on intermediate and high impedance samples. More details can be found in the TN#05

My MTZ-35 does not beep when I turn it on? How can I proceed?

If the power led is off when you switch on the MTZ-35, check the fuses located on the rear panel of the instrument. If a fuse is blown replace it with a new one rated at 3.15A. You can use the two 2A rapid fuses provided at the purchase of the MTZ-35.

How do I check the accuracy of results given by the MTZ-35?

Any instrument is prone to a drift in its accuracy with time and use. In order to check the accuracy of the MTZ-35, use a high accuracy resistor or capacitor and check the measured resistance/capacitance with their corresponding nominal resistance/capacitance.

Which communication port should I connect the MTZ-35 to?

When you install MT-Lab® software the driver of the MTZ-35 is also installed and two virtual communication ports are generated. To access to these communication ports go to “Control Panel”>”External Devices”> “Ports(COM & LPT)”. You can see two virtual communication ports “USB serial port (COM N)” and “USB serial port (COM N+1)”. Select the one with the high order (COM N+1).

I performed a measurement on a capacitor with a nominal capacitance 100 pF I got 320 pF capacitance value. Do I need to calibrate my MTZ-35?

The measured capacitance should coincide with the nominal capacitance. your measurement seems to be performed without compensation. Perform open-circuit and short circuit compensation and then perform impedance measurement on the capacitor. More details can be found in the TN#01 and AN#04

I receive many cell cables with MTZ-35 which one should I use?

The MTZ-35 is provided with two sets of cables:

  • A set of four cables (x1 m) for four-point measurement dedicated for impedance measurements on low impedance samples (lower than 1 Ω)
  • A set of three cables with a Tee connector for two-point measurement for impedance measurements on intermediate and high impedance samples. More details can be found in the TN#05

My MTZ-35 does not beep when I turn it on? How can I proceed?

If the power led is off when you switch on the MTZ-35, check the fuses located on the rear panel of the instrument. If a fuse is blown replace it with a new one rated at 3.15A. You can use the two 2A rapid fuses provided at the purchase of the MTZ-35.

How do I check the accuracy of results given by the MTZ-35?

Any instrument is prone to a drift in its accuracy with time and use. In order to check the accuracy of the MTZ-35, use a high accuracy resistor or capacitor and check the measured resistance/capacitance with their corresponding nominal resistance/capacitance.

Which communication port should I connect the MTZ-35 to?

When you install MT-Lab® software the driver of the MTZ-35 is also installed and two virtual communication ports are generated. To access to these communication ports go to “Control Panel”>”External Devices”> “Ports(COM & LPT)”. You can see two virtual communication ports “USB serial port (COM N)” and “USB serial port (COM N+1)”. Select the one with the high order (COM N+1).

I performed a measurement on a capacitor with a nominal capacitance 100 pF I got 320 pF capacitance value. Do I need to calibrate my MTZ-35?

The measured capacitance should coincide with the nominal capacitance. your measurement seems to be performed without compensation. Perform open-circuit and short circuit compensation and then perform impedance measurement on the capacitor. More details can be found in the TN#01 and AN#04

I receive many cell cables with MTZ-35 which one should I use?

The MTZ-35 is provided with two sets of cables:

  • A set of four cables (x1 m) for four-point measurement dedicated for impedance measurements on low impedance samples (lower than 1 Ω)
  • A set of three cables with a Tee connector for two-point measurement for impedance measurements on intermediate and high impedance samples. More details can be found in the TN#05

My MTZ-35 does not beep when I turn it on? How can I proceed?

If the power led is off when you switch on the MTZ-35, check the fuses located on the rear panel of the instrument. If a fuse is blown replace it with a new one rated at 3.15A. You can use the two 2A rapid fuses provided at the purchase of the MTZ-35.

How do I check the accuracy of results given by the MTZ-35?

Any instrument is prone to a drift in its accuracy with time and use. In order to check the accuracy of the MTZ-35, use a high accuracy resistor or capacitor and check the measured resistance/capacitance with their corresponding nominal resistance/capacitance.

Which communication port should I connect the MTZ-35 to?

When you install MT-Lab® software the driver of the MTZ-35 is also installed and two virtual communication ports are generated. To access to these communication ports go to “Control Panel”>”External Devices”> “Ports(COM & LPT)”. You can see two virtual communication ports “USB serial port (COM N)” and “USB serial port (COM N+1)”. Select the one with the high order (COM N+1).

I performed a measurement on a capacitor with a nominal capacitance 100 pF I got 320 pF capacitance value. Do I need to calibrate my MTZ-35?

The measured capacitance should coincide with the nominal capacitance. your measurement seems to be performed without compensation. Perform open-circuit and short circuit compensation and then perform impedance measurement on the capacitor. More details can be found in the TN#01 and AN#04

I receive many cell cables with MTZ-35 which one should I use?

The MTZ-35 is provided with two sets of cables:

  • A set of four cables (x1 m) for four-point measurement dedicated for impedance measurements on low impedance samples (lower than 1 Ω)
  • A set of three cables with a Tee connector for two-point measurement for impedance measurements on intermediate and high impedance samples. More details can be found in the TN#05

My MTZ-35 does not beep when I turn it on? How can I proceed?

If the power led is off when you switch on the MTZ-35, check the fuses located on the rear panel of the instrument. If a fuse is blown replace it with a new one rated at 3.15A. You can use the two 2A rapid fuses provided at the purchase of the MTZ-35.

How do I check the accuracy of results given by the MTZ-35?

Any instrument is prone to a drift in its accuracy with time and use. In order to check the accuracy of the MTZ-35, use a high accuracy resistor or capacitor and check the measured resistance/capacitance with their corresponding nominal resistance/capacitance.

Which communication port should I connect the MTZ-35 to?

When you install MT-Lab® software the driver of the MTZ-35 is also installed and two virtual communication ports are generated. To access to these communication ports go to “Control Panel”>”External Devices”> “Ports(COM & LPT)”. You can see two virtual communication ports “USB serial port (COM N)” and “USB serial port (COM N+1)”. Select the one with the high order (COM N+1).

I performed a measurement on a capacitor with a nominal capacitance 100 pF I got 320 pF capacitance value. Do I need to calibrate my MTZ-35?

The measured capacitance should coincide with the nominal capacitance. your measurement seems to be performed without compensation. Perform open-circuit and short circuit compensation and then perform impedance measurement on the capacitor. More details can be found in the TN#01 and AN#04

Accessories

You may want to complete your set-up with.

The following sample holders are relevant to this product and may be of interest.

Greater Scope. Increased Flexibility

These products may help you go further with you research.

Related topics

Request a quote.

Our team is ready to help

Contact us